AX-09 Driver Ver.1.0.0 for Windows Vista® 32-bit Edition

(Note)
In no event shall Roland Corporation ("Roland") be liable to end-users for any damages whatsoever, including but not limited to financial damages for loss of business profits or business information arising from the use of, or inability to use this product. The foregoing provision is effective even if Roland has been advised of the possibility of such damages.

*All files and other material contained in this folder are copyrighted by the Roland. Any alteration, modification, duplication, distribution, or reproduction of this material is prohibited. Additionally, Roland reserves the right to make changes to these programs and files without prior notice.
* Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation.
*All product names mentioned in this document are trademarks or registered trademarks of their respective owners.

About this driver

This is the AX-09 driver for Microsoft® Windows Vista® 32-bit Edition.

System requirements

This driver has the following requirements.

Operating System
Microsoft® Windows Vista® 32-bit Edition
*This does not work with the 64-bit Edition of Windows Vista.
Computer
A computer with a USB connector that supports USB Specification Revision 1.1 or higher
*Macintosh computers running Microsoft Windows are not supported.

Cautions and Limitations


Installation

*To reinstall or update the driver, refer to "To reinstall."
  1. Start up Windows with all USB cables disconnected.
    (except for keyboard and mouse)
  2. Exit all applications before you begin the installation.
  3. Double-click the Setup icon.
  4. *If a message informs you that "Driver installation must be performed by an administrator," you must log on to Windows as a user whose Account Type is Administrator, and then perform the installation.
  5. A confirmation screen regarding User Account Control will appear, click [Continue].
  6. The message "AX-09 Driver will be installed on your computer. ---" will appear. Click [Next].
    *If any other message appears, follow the directions of the message.
  7. Click [Next] to begin installation.
  8. If a dialog box regarding Windows Security appears, click [Install].
  9. The message "Ready to install the driver. ---" will appear.
    *If any other message appears, follow the directions of the message.
  10. Use a USB cable to connect the AX-09 to your computer, then turn on the AX-09.
    The driver will be installed automatically.
  11. When the "Installation has been completed." message appears, installation has been completed.
    Click [Close] to close the "Driver Setup" dialog box.
  12. If the "System Settings Change" dialog box appears, click [Yes] to restart Windows.
  13. Refer to "Before you begin," and make the necessary settings for using the AX-09. You won't be able to use the AX-09 unless you make these settings.
    *If you are unable to use the AX-09 after connecting it, it's possible that a problem has occurred. Refer to "Troubleshooting."

Before you begin

Input/output device settings for your application

In the application(s) that you intend to use, specify the MIDI device they are to use. (For details on this setting, refer to the owner's manual for your application.)

*If you are unable to select the AX-09 device, a problem may have occurred. Refer to "Troubleshooting."

MIDI input/output device

*In the Windows Media Player, the MIDI input/output device of AX-09 cannot be used.
Please select the following device in your MIDI compatible application.
[MIDI OUT devices]
AX-09
 
[MIDI IN devices]
AX-09
 

To change the settings

To change or verify settings

  1. When changing driver settings, always make sure to first quit all applications using the AX-09. This is unnecessary when only checking the settings.
  2. Open "Control Panel," click "Additional Options," and then click "AX-09."
    *If you're using the Classic View, double-click "AX-09."
  3. The "AX-09 Driver Settings" dialog box will appear.
  4. To modify the settings, make the changes and click [OK]. To simply check the settings, be sure to click [Cancel] after viewing the settings.
    *For details on the setting items, refer to "About the items in the Settings dialog box."

About the items in the Settings dialog box

The "Light Load" check box
Normally, you should leave this check box cleared.
*The modified setting will take effect after you turn the power of the AX-09 on/off.
 
"Show README" button
This button displays the README file (this document).
 
Information
This field shows the driver version.

To reinstall

  1. Delete the driver as described in "To uninstall."
    *When you uninstall, the settings of the Driver Settings dialog box will be initialized. For details on the setting items, refer to "About the items in the Settings dialog box."
  2. Install the driver as described in "Installation."

To uninstall

  1. Start up Windows with all USB cables disconnected.
    (except for keyboard and mouse)
  2. Exit all applications before you begin the uninstallation.
  3. Open "Control Panel" and click "Uninstall a program."
    *If you're using the Classic View, double-click "Programs and Features."
  4. In the list, choose "AX-09 Driver", and click "Uninstall/Change."
  5. If a dialog box regarding User Account Control appears, click [Continue].
  6. *If you are asked to enter the password for an administrative account, log on to Windows as a user whose Account Type is Administrator, and then perform the uninstallation.
  7. The display will indicate "The installed AX-09 Driver will be uninstalled." and click the [OK].
  8. When the message "Uninstallation was completed." is displayed, click [OK] to restart Windows.

Troubleshooting

Cannot install/uninstall the driver

Is the AX-09 set to VENDER mode?
Set the AX-09 to VENDER mode.
 
Are you logged onto Windows with the appropriate user rights?
You must log on to Windows as a user whose Account Type is Administrator.
*For more information regarding this, consult your computer system administrator.
 

Cannot select/use the AX-09 device

Was the driver installed correctly?
If you can't use the AX-09 even though you've installed the driver, the driver might not be installed correctly. Use the procedure described in "To reinstall" to reinstall the driver.
 
Could the AX-09 be in use by other software?
Exit all applications that are using the AX-09, and turn the power of the AX-09 off, then on again.
If this does not solve the problem, use the procedure described in "To reinstall" to reinstall the driver.
 
Is the AX-09 MIDI device name displayed?
If the device name is not displayed, exit all applications that are using the AX-09, and turn the power of the AX-09 off, then on again.
If this does not solve the problem, use the procedure described in "To reinstall" to reinstall the driver.
 
Did the computer enter a Sleep mode while the AX-09 was connected with its power turned on?
If the AX-09 does not work correctly after resuming from Sleep mode, you should exit all applications that use the AX-09, and then turn the power of the AX-09 off and on again.
 
Was the USB cable disconnected and reconnected while the AX-09 was being used, or was the power of the AX-09 turned off, then on again?
If the USB cable is disconnected and reconnected while the AX-09 is in use, or if the power of the AX-09 is turned off, then on again, it may no longer operate correctly. If this occurs, exit all applications that are using the AX-09, and turn the power of the AX-09 off, then on again.
 
On some computers, if the AX-09 is connected while Windows starts up, the driver will not be loaded correctly, and it will not be possible to use the AX-09 via USB.
If this occurs, start up Windows before you turn on the power of the AX-09 or connect it.
 

A number such as "2-" is now displayed at the beginning of the device name

Could you have connected the AX-09 to a different USB port?
If you connect the AX-09 to a different USB port, the operating system may automatically add a number to the beginning of the device name.
Even if this occurs, it will not cause any problems with the operation of the AX-09.
*If you want to restore the device name that does not have this added number, connect the AX-09 to the same USB port as when you installed it, or reinstall the driver as described in "To reinstall."

Cannot playback or record

Was the driver installed correctly?
 
Could the AX-09 be in use by other software?
 
Did you make settings as described in "Before you begin" so that the AX-09 driver could be used?
The AX-09 cannot be used unless you make these settings. Refer to the sections on "Before you begin."
 
Could you have entered Sleep mode during playback or recording?
If the AX-09 does not work correctly after resuming from Sleep mode, you should exit all applications that use the AX-09, and then turn the power of the AX-09 off and on again.
 
During playback or recording, did you turn the power of the AX-09 on/off, or disconnect and reconnect the USB cable?
If you turn the power of the AX-09 on/off or disconnect and reconnect the USB cable during playback or recording, the AX-09 will no longer be able to play back or record. Stop playback or recording, and then start playback or recording once again. If you are still unable to play back or record, quit all programs that are using the AX-09, then turn the AX-09 off and then on again.
 

Part of the playback is wrong: e.g., notes are broken off prematurely, or some notes are lost

Problems may be solved by making the settings shown below.

Try updating the driver of your display adaptor
You may be able to eliminate clicks and pops by updating the driver for the display adaptor installed in your computer.
 
Windows Update / Microsoft Update
You may be able to solve the problem by updating your system with "Windows Update" or "Microsoft Update" provided by Microsoft.
 
Check the power management settings
  1. Open "Control Panel," click "System and Maintenance," and then click "Power Options."
    *If you're using the Classic View, double-click "Power Options."
  2. In "Select a power plan," choose "High performance."
  3. In the High performance area, click "Change plan settings."
  4. Click "Change advanced power settings."
  5. In the Advanced Settings, click the “+” symbol for "Hard Disk," and click the “+”symbol for "Turn off hard disk after" to open it.
  6. Click "Setting (Minutes)," and click the down arrow to change the setting to "Never."
  7. Click [OK] to close the Power Options window.
  8. Close the "Edit Plan Settings" screen.
"Performance Options" settings of System Properties
  1. Open "Control Panel," click "System and Maintenance," and then click "System."
    *If you're using the Classic View, double-click "System."
  2. In the Tasks shown at the left, click "Advanced system settings."
  3. If a dialog box regarding User Account Control appears, click [Continue].
    *If you are asked to enter the password of an Administrator account, log on to Windows as a user whose Account Type is Administrator, then perform the settings again.
  4. Click [Settings] of the Performance section, and then click the [Advanced] tab.
  5. Select "Background services," and click [OK].
  6. Click [OK] to close "System Properties."
Such problems may be solved if you check the "Light Load" check box in the Driver Settings dialog box.
If you wish to modify or verify the settings, use the procedure described in "To change the settings."
*The modified setting will take effect after you turn the power of the AX-09 on/off. Unless you experience problems, use the unchecked (initial) setting.

Copyright (C) 2009 Roland Corporation. All rights reserved.